Weider 15CT Uživatelský manuál

CAUTIONRead all precautions and instruc-tions in this manual before usingthis equipment. Save this manualfor future reference.Model No. WESY17011Seria

1014. Locate the Long “U”-Bracket (57) that is pre-assembled with a 90mm Pulley (15) and a CableTrap (not shown). Route the Long Cable (58)around the

111721151215669214Bracket172517. Using an M10 x 80mm Bolt (25), an M10 Washer(9), and an M10 Nylon Locknut (21), secure a90mm Pulley (15) and a Cable

1221. Route the Short Cable (23) up around the 90mm Pulley (15) attached to the upper hole inthe Press Frame (17). Be sure that the Cable isrouted aro

23. Attach the Backrest (41) to the Front Upright (42)with two M6 x 63mm Screws (43) and two M6Washers (10).SEAT ASSEMBLY23414210431324. Press a 38mm

1426. Rest the Seat Frame (36) on the indicated pin inthe Front Upright (42). Attach the Seat Frame tothe Front Upright with an M8 x 67mm CarriageBolt

1530. Make sure that all parts have been properly tightened. The use of all remaining parts will be explained inADJUSTMENTS, beginning on the followin

16ADJUSTMENTThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t

17ATTACHING THE LEG LEVER TO THE LOWPULLEY STATIONTo use the Leg Lever (29), the seat must be attachedto the front upright (see ATTACHING AND REMOV-IN

18WEIGHT ON PRESS ARM BUTTERFLY ARM LOW PULLEY/ HIGH PULLEYWEIGHT (lbs.) (lbs.) LEG LEVER (lbs.)CARRIAGE (lbs.)012710 1052211181610 31 15 25 2115 40 2

19TROUBLE-SHOOTING AND MAINTENANCE Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immedi-ately

2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20CABLE DIAGRAMThe cable diagram below shows the proper routing of the Short Cable (23) and the Long Cable (58). Use the dia-gram to be sure that the

21NOTES

22Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. PART LIST—Model No. WESY17011 R0802BKey No. Qty. De

152356151235723213551145141271675062163626362474844454445134038371832283034102243630341461329343028494632303449494622392559172152444486654313126606049

M10 Eyebolt (35) M6 Nylon Locknut (2)M8 Nylon Locknut (3)M10 Nylon Locknut (21)M6 Washer (10)M8 Washer (8)M6 x 50mm Screw (24)M6 x 63mm Screw (43)M8 x

M10 x 60mm Bolt (7)M10 x 45mm Bolt (12)M10 x 90mm Bolt (16)M10 x 80mm Bolt (25)M10 x 198mm Bolt (59)M8 x 70mm Bolt (11)M8 x 67mm Bolt (61)M8 x 115mm B

50mm Square Outer Cap (51)50mm Square Inner Cap (27)38mm Square Inner Cap (32)19mm Round Inner Cap (34)45mm Square Inner Cap (44)25mm Round Inner Cap

To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday throughFriday, 6 a.m. until 6 p.m. Mountain Time

1. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibility of the owner to en

4ASSEMBLED DIMENSIONS: Height: 76 in.Width: 37 in. Length: 48 in. Foot PlateLow Pulley StationHigh Pulley StationLat BarLeg LeverButterfly ArmsPress A

5Make sure you have the following tools:• Two adjustable wrenches• One standard screwdriver• One phillips screwdriver• One rubber mallet•You will

61563551511412741. Before beginning assembly, be sure that youhave read and understand the information inthe box on the previous page.Press a 50mm Squ

744TubeWeldedSpacers1759Lubricate21993. Press a 45mm Square Inner Cap (44) into eachend of the crossbar on the Top Frame (55). Presstwo 25mm Round Inn

87. Lubricate both axles on the Top Frame (55). Slidethe Right Arm (48) onto the right axle. Note: Becareful not to confuse the Right Arm with theLeft

911105058747582172165064210. Wrap the Long Cable (58) around a “V”-Pulley(6). Attach the “V”-Pulley and a Long Cable Trap(50) to the indicated bracket